Amplifier and Enclosure Kit for LASERBEAM-DUAL Filter Modules (DSP module included) - (BOXA-DUAL)
The popular LASERBEAM-DUAL filters are ideal for incorporating into your own designs. However, for additional flexibility we have designed this great amplifier/enclosure kit which will allow your LASERBEAM-DUAL filter module (included) to be used with all your favourite radios. It has a professional look to compliment your shack.
The BOXA-DUAL kit consists of a PCB that the filter module (included) will plug into, together with an audio amplifier. The front panel features the CW Tuning LED (Sig) and Overload LED (Lvl) as well as a bandwidth switch (W/N) and volume control (Vol). The rear panel has 3.5 mm stereo sockets for audio in and out as well as a power socket for a DC supply (5-15 Volts).
As supplied, the board will drive headphones or a small loudspeaker. By changing two resistors, audio output can be increased up to 1.5 Watts which will drive loudspeaker. Because the filter module is a plug-in unit you can swap between different LASERBEAM-DUAL modules depending on your application.
The BOXA-DUAL enclosure has laser-cut gold-effect panels which screw into a rugged aluminium case. Power input is via 2.1 mm power socket (plug supplied).
The kit uses all through-hole components and is an easy build for a beginner. Build time about 40 minutes. Click here for instructions.
A 3.5 mm to 3.5 mm jack to jack lead might be handy so we got some in. Click here.
Cable for your power lead could be useful. Click here.
Size: 85 x 63 x 30 mm
Weight: 136 grams
Supply Voltage: 5 - 15 Volts
Current: 70 mA - using headphones
Power output: 1.5 Watts maximum into 8 Ohms (maximum depends on internal resistor values)
Also available from our international agent(s):
18 Reviews Hide Reviews Show Reviews
Very pleased with the operation. A great help when needed to pull in the cw signal when local noise interferes.
I have bought two of these in the last year or so. Excellent kit that went together perfectly well and transformed my listening pleasure with an Icom R71 and NRD525 on 40, 60 & 80m CW. Strongly recommend the narrow CW filter to anyone using a RX without IF CW filters and no DSP. The kit really makes a difference!
With very little experience, I was able to build this kit in under 2 hours.
It works great with my FT-817 and homebrew rigs. It can even clean up the receiver audio of a Pixie!
I have also used it in-line with my interface working digital modes and it has made a huge difference in the waterfall.
I dropped hints to the family of what would be a good Xmas and birthday pressy...glad I did...easy to build with good instructions and makes cw copy on the 817 very pleasant ....thanks richard...
Hint ...do a test run with self tappers before affixing the end plates as screws are tight and easy to slip and scratch panel with driver.
A loth of cw operators like me have experienced fatique when listening to kx3 rig on cw for longer periodes. This have been very irritating when considering the price of the rig and that cw is one of the main modes for low power operation. I got the idea to try to use the Laserbeam-Dual on the rig. It turns out that I am much less fatigued after 1 or 2 houers with listening. I manipulate the origional filter and the 2 position cw filter on the Laserbeam-Dual trying to decrease the noise as much as possible. Quit easy when You get into it. To have an audio amplifier is important because the build in audio amplifier is a bit weak on kx3 when driving an external audiofilter
Amazing. Using digital filters you can usually expect a
delay between in and out. That one is here less than
approx. 10 ms, which is an excellent value. Digital devices
most of all have their own RF emission across the shortwave
bands due to MCU clock rate, which one is here so low, you
could hard identify by sensitive measurements. Thus DX
shortwave reception on testing never was affected by
unwanted MCU clock emission using that device. The related
noise on AF-output is extremely low on amplifier output,
you cannot hear. It seems an internal limiter is always
working in the background, you do not notice on normal
operation, but what is a good extra feature. In comparison
to "normal" OP-Amp filters, there are no distortions
caused on resonance peaks.
The quality of kit components is outstanding. The service
contact is excellent, too, by the way.
Great to have a well designed enclosure kit which included a small audio amplifier
Have had the filter a few weeks and have been using it with my IC703 both in the shack and portable. Durning our QRP groups outings the guys can't believe the single signal copy on CW. The only minus is it draws about 200mA and can kill a 9V battery overnight if you forget to unplug it 73, Jim KI1H
I was originally going to put the SOTABeams filter module directly into the FT-817. But then I realized I wanted more flexibility than having it permanently installed in there, even though it's more efficient in terms of space (and probably power). So then I ordered this kit and the filter module for CW (wide/narrow).
Wow -- I'm really impressed! Plug it in, tune around with it set to "Wide" and then switch over to "Narrow" and the signal is super-clear. Makes it really easy to pull things out of the noise and/or other stations.
This makes the FT-817 (or any other filterless radio) very useable on CW.
The kit is a pretty easy build if you've ever built kits before, and I'm quite certain a total beginner could do it, too, if they've ever done soldering.
I had purchased a LASERBEAM-DUAL SSB/CW module several months ago and had not done anything to case it up, other than some thinking. I purchased the amplifier/enclosure kit, which arrived in a reasonable time. The instructions were clear and easy to follow. I quickly had it all assembled and integrated. Worked great on the first try. The combination makes the FT-817 much easier to use.